英國GRIMM格林進口鍋爐給水泵 UK GRIMM Imported boiler feed pump

英國GRIMM格林進口鍋爐給水泵概述：
          進口鍋爐給水泵系臥式單級多級分段式離心泵，可供輸送清水或物理化學性質類似于清水的液體，適用于中、低壓鍋爐或次高壓鍋爐給水，也適用于工廠或城市高壓給排水。輸送介質溫度為-20℃～105℃，進口允許壓力小于0.6MPa。
          進口鍋爐給水泵采用了英國格林推薦使用的高效節能產品的水力模型。具有效率高、性能范圍廣、運轉安全和平穩、噪音低、壽命長、安裝維修方便等優點。

英國GRIMM格林進口鍋爐給水泵結構特點：

1、泵的進、出水口均為垂直向上，通過拉緊螺栓將泵的進水段、中段、出水段、軸承體等泵殼體部分聯結成一體。根據泵的揚程選擇泵的級數。
2、泵的轉子部分主要由軸及安裝在軸上的葉輪、軸套、平衡盤等零件組成，其中葉輪的數量根據泵的級數而定。軸上零件用平鍵和軸螺母緊固使之與軸聯為一體。整個轉子由兩端滾動軸承或滑動軸承支承。軸承按型號不同而定，均不承受軸向力，其軸向力由平衡盤平衡。泵在運行中允許轉子在泵殼中軸向游動，不能采用向心球 軸承。滾動軸承用油脂潤滑，滑動軸承用稀油潤滑中，并用油環進行自潤滑，循環水冷卻。
3、泵的進水段、中段、出水段之間的密封均采用二硫化鉬潤滑脂密封，轉子部分與固定部分之間裝有密封環、導葉套等進行密封，當密封環和導葉套的磨損程度己影響泵的工作性能時應予更換。

4、軸的密封形式有機械密封和填料密封兩種。泵采用填料密封時，填料環的位置安放要正確，填料的松緊程度必須適當，以液體能一滴一滴滲出為宜。泵各種密封元件裝在密封箱內，箱內要通入一定的壓力的水，起水封、水冷或水潤滑作用。在軸封處裝有可更換的軸套，保護泵軸。 

5、高壓泵一般采用滑動軸承、稀油潤滑結構，可采用滑動軸承、稀油潤滑，也可采用滾動軸承、干油潤滑結構，其余型號均采用滾動軸承、干油潤滑結構。中、低壓泵的主要零件材料一般采用優質鑄鐵，次高壓泵主要零件采用鑄鋼或不銹鋼。該系列泵通過彈性聯軸器由原電機直接驅動，從原電機方向看，泵為順時針?lè)较蛐�轉。

英國GRIMM格林進口鍋爐給水泵特點： 
1、水力模型先進，效率高，性能范圍廣。
2、泵運行平穩，噪音低。 
3、軸封采用軟填料密封或機械密封，密封安全可靠、結構簡單，維修方便快捷。
4、軸為全封結構，確保了不與介質接觸，不銹蝕，使用壽命長。

英國GRIMM格林進口鍋爐給水泵主要參數：
流量：3.75-500m3/h
揚程：55-680m
口徑：50-200mm
轉速：1450-2950r/min
功率：2.2-400kw
溫度范圍：≤105℃
工作壓力：≤3.0Mpa
材質：鑄鐵、鑄鋼、不銹鋼

英國GRIMM格林進口鍋爐給水泵適用范圍：
?? 適用于工業和城市給排水、高層建筑增壓供水，園林噴灌、消防增壓、遠距離送水、采暖、浴室等冷暖水循環增壓及設備配套等，尤其適用于小型鍋爐給水。

UK GRIMM Imported boiler feed pump summary:

       Imported boiler feedwater pump system for Horizontal single-stage multistage centrifugal pump, can be used to transport water or similar physical and chemical properties of liquid water, suitable for medium and low pressure boiler or pressure boiler feedwater, also applies to the factory or city high pressure water supply and drainage. The medium temperature is -20 ~ 105 DEG C, and the inlet pressure is less than 0.6MPa.

        The imported boiler feed pump adopts the hydraulic model of efficient energy-saving products recommended by Green. The utility model has the advantages of high efficiency, wide performance range, safe and steady operation, low noise, long service life, convenient installation and maintenance, etc..

UK GRIMM Imported boiler feed pump structure characteristics:

1.The pump inlet and outlet are vertical upward, through the tension bolt will pump the water inlet, middle section, the water outlet section, the bearing body and so on pump shell part is connected as a whole. Select the series of pumps according to the pump lift.

2.The rotor part of the pump mainly by the shaft and the impeller installed on the shaft, shaft sleeve, balance plate and other parts, in which the number of impeller according to the pump series and fixed. The shaft parts are fastened by flat keys and shaft nuts so as to be connected with the shaft as a whole. The whole rotor is supported by rolling bearings or sliding bearings at both ends. The bearings are different according to the model, and they do not bear axial force. The axial force of the bearings is balanced by the balance disc. In operation, the rotor is allowed to swim axially in the pump housing, and radial ball bearings cannot be used. The rolling bearings are lubricated with grease. The sliding bearings are lubricated by thin oil, and lubricated by oil rings. The circulating water is cooled.

3.Pump seal between the water inlet section, the middle section of the water are used MoS2 grease seal, a sealing ring, a guide vane sleeve for sealing is arranged between the rotor part and the fixed part, when the sealing ring and the guide vane sleeve wear should be replaced so affect the pump performance when.

4.The shaft seal in the form of mechanical seal and packing seal two. Pump packing seal, the packing ring position should be placed properly, the tightness of the packing must be appropriate, with a drop of liquid can be a drop of appropriate.  All kinds of sealing elements are installed in the sealed box. The water in the box must pass through a certain pressure, and the water seal, water cooling or water lubrication can be used. A replaceable shaft sleeve is arranged at the shaft seal to protect the pump shaft.

5.High pressure pumps generally use the oil lubrication structure, sliding bearing, the sliding bearing, oil lubrication, also can use rolling bearing, grease lubrication structure, the other models are the rolling bearing, grease lubrication structure. The main parts of medium and low pressure pumps are made of high quality cast iron, and the main parts of secondary pumps are made of cast steel or stainless steel. The series pump is driven directly by the original motor through an elastic coupling, and the pump rotates clockwise in the direction of the original motor.

UK GRIMM Imported boiler feed pump characteristic:

1.Hydraulic model advanced, high efficiency, wide range of performance.

2.The pump runs smoothly and the noise is low.

3.Tthe shaft seal adopts soft packing seal or mechanical seal, the sealing is safe and reliable, the structure is simple, and the maintenance is convenient and quick.

4.The shaft is a full seal structure, to ensure that no contact with the media, no rust, long service life.

UK GRIMM Imported boiler feed pump technical parameter:

Flow rate: 3.75-500m3/h

Lift: 55-680m

Caliber: 50-200mm

Speed: 1450-2950r/min

Power: 2.2-400kw

Temperature range: less than or equal to 105 DEG C

Working pressure: 3.0Mpa

Material: cast iron, stainless steel

UK GRIMM Imported boiler feed pump scope of application:

       Suitable for the industry and the city water supply and drainage, high-rise building pressurized water, garden irrigation, fire booster, long-distance water, heating, bathroom pressurization of cold and hot water circulation equipment, especially suitable for boiler.